Table Of Contents

Previous topic


Next topic


This Page


Calculates magnitudes of different types.


The purpose of scmag is to compute magnitudes. It takes amplitudes and origins as input and produces StationMagnitudes and Magnitudes as output. The resulting magnitudes are sent to the "MAGNITUDE" group. scmag doesn’t access any waveforms. It only uses amplitudes previously calculated, e.g. by scamp. The purpose of scmag is the decoupling of magnitude computation from amplitude measurements. This allows several modules to generate amplitudes concurrently, like scautopick and scamp. As soon as an origin comes in, the amplitudes related to the picks are taken either from the memory buffer or the database to compute the magnitudes. Currently the following magnitude types are implemented:

Local magnitude calculated on the vertical component using a correction term to fit with the standard ML
Local magnitude calculated on the horizontal components to SED specifications.
Narrow band body wave magnitude using a third order Butterworth filter with corner frequencies of 0.7 and 2.0 Hz.
Broad band body wave magnitude.
The body wave magnitude of Tsuboi et al. (1995)

Additionally, scmag computes the following derived magnitudes:

Estimation of the moment magnitude Mw based on mB using the Mw vs. mB regression of Bormann and Saul (2008)
Estimation of the moment magnitude Mw based on Mwp using the Mw vs. Mwp regression of Whitmore et al. (2002).
Summary magnitude, which consists of a weighted average of the individual magnitudes and attempts to be a best possible compromise between all magnitudes. See below for configuration and also scevent for how to add the summary magnitude to the list of possible preferred magnitudes or how to make it always preferred.
Estimation of the moment magnitude Mw based on a weighted average of other magnitudes, currently MLv, mb and Mw(mB), in future possibly other magnitudes as well, especially those suitable for very large events. The purpose of Mw(avg) is to have, at any stage during the processing, a “best possible” estimation of the magnitude by combining all available magnitudes into a single, weighted average. Initially the average will consist of only MLv and/or mb measurements, but as soon as Mw(mB) measurements become available, these (and in future other large-event magnitudes) become progressively more weight in the average.

Summary magnitude

scmag can compute a summary magnitude which is a weighted sum of all available magnitudes. This magnitude is called M and is computed as follows:

M = \frac{\sum w_{i} M_{i}}{\sum w_i} w_{i} = a_i stacount(M_{i}) + b_i

The coefficients a and b can be configured per magnitude type. Furthermore each magnitude type can be included or excluded from the summary magnitude calculation.



scmag inherits global options.


Type: list:string

Definition of amplitude types to be calculated. Default is MLv, mb, mB, Mwp.


Type: int

Interval between 2 sending processes. The interval has influence how often information is updated. Default is 1.


Type: double

The minimum weight of an arrival to be used for magnitude calculations. Default is 0.5.


summaryMagnitude.* The summary magnitude is building a weighted summary above all defined magnitude types. The single magnitude value is multiplied with the magnitude type specific weight. This is summed up for all magnitude types and the resulting sum is divided through the sum of all weights.


Type: boolean

Enables summary magnitude calculation. Default is true.


Type: string

Define the type/name of the summary magnitude. Default is M.


Type: int

This is the minimum station magnitude required for any magnitude to contribute to the summary magnitude at all. If this is set to 4 then no magnitude with less than 4 station magnitudes is taken into consideration even if this results in no summary magnitude at all. For this reason, the default here is 1 but in a purely automatic system it should be higher, at least 4 is recommended. Default is 4.


Type: list:string

Define the magnitude types to be excluded from the summary magnitude calculation.


Type: list:string

Define the magnitude types to be included in the summary magnitude calculation.


summaryMagnitude.coefficients.* Define the coefficients to calculate the weight of a magnitude. weight = a*magStationCount+b


Type: list:string

Define the coefficients a. Unnamed values define the default value. Default is 0, Mw(mB):0.4, Mw(Mwp):0.4.


Type: list:string

Define the coefficients b. Unnamed values define the default value. Default is 1, MLv:2, Mw(mB):-1, Mw(Mwp):-1.


Type: list:string

Defines the average method to use when computing the network magnitude. To define the average method per magnitude type append the type, eg: "magnitudes.average = default, MLv:median"

The default behaviour is to compute the mean if less than 4 contributed station magnitudes exist otherwise a trimmed mean of 25 percent is used. Options are "default", "mean" and "trimmedMean". Default is default.



-h, --help

show help message.

-V, --version

show version information

--config-file arg

Use alternative configuration file. When this option is used the loading of all stages is disabled. Only the given configuration file is parsed and used. To use another name for the configuration create a symbolic link of the application or copy it, eg scautopick -> scautopick2.

--plugins arg

Load given plugins.

-D, --daemon

Run as daemon. This means the application will fork itself and doesn't need to be started with &.

--auto-shutdown arg

Enable/disable self-shutdown because a master module shutdown. This only works when messaging is enabled and the master module sends a shutdown message (enabled with --start-stop-msg for the master module).

--shutdown-master-module arg

Sets the name of the master-module used for auto-shutdown. This is the application name of the module actually started. If symlinks are used then it is the name of the symlinked application.

--shutdown-master-username arg

Sets the name of the master-username of the messaging used for auto-shutdown. If "shutdown-master-module" is given as well this parameter is ignored.

-x, --expiry time

Time span in hours after which objects expire.


--verbosity arg

Verbosity level [0..4]. 0:quiet, 1:error, 2:warning, 3:info, 4:debug

-v, --v

Increase verbosity level (may be repeated, eg. -vv)

-q, --quiet

Quiet mode: no logging output

--component arg

Limits the logging to a certain component. This option can be given more than once.

-s, --syslog

Use syslog logging back end. The output usually goes to /var/lib/messages.

-l, --lockfile arg

Path to lock file.

--console arg

Send log output to stdout.


Debug mode: --verbosity=4 --console=1

--log-file arg

Use alternative log file.


-u, --user arg

Overrides configuration parameter connection.username.

-H, --host arg

Overrides configuration parameter connection.server.

-t, --timeout arg

Overrides configuration parameter connection.timeout.

-g, --primary-group arg

Overrides configuration parameter connection.primaryGroup.

-S, --subscribe-group arg

A group to subscribe to. This option can be given more than once.

--encoding arg

Overrides configuration parameter connection.encoding.

--start-stop-msg arg

Sets sending of a start- and a stop message.



List all supported database drivers.

-d, --database arg

The database connection string, format: service://user:pwd@host/database. "service" is the name of the database driver which can be queried with "--db-driver-list".

--config-module arg

The configmodule to use.

--inventory-db arg

Load the inventory from the given database or file, format: [service://]location


Do not use the database at all